113 lines
4.1 KiB
Markdown
113 lines
4.1 KiB
Markdown
# Trikke Motion Telemetry Logger
|
|
|
|
Prototype v0 firmware for a Seeed Studio XIAO ESP32-C3 with an ADXL345
|
|
accelerometer and L3G4200D gyroscope on a shared I2C bus.
|
|
|
|
This milestone does four things:
|
|
|
|
1. Detects and verifies both sensors by their identification registers.
|
|
2. Configures each sensor for a nominal 100 Hz raw output rate.
|
|
3. Emits timestamped, sensor-native raw readings over the XIAO USB connection.
|
|
4. Maps both sensors into a shared enclosure coordinate frame and emits both raw
|
|
and calibrated readings.
|
|
|
|
BLE transport and phone-side storage come after the wired sensor path is proven.
|
|
|
|
## Wiring
|
|
|
|
| Signal | XIAO pin | ESP32-C3 GPIO |
|
|
| --- | --- | --- |
|
|
| SDA | D4 | GPIO6 |
|
|
| SCL | D5 | GPIO7 |
|
|
| Sensor power | 3V3 | — |
|
|
| Sensor ground | GND | — |
|
|
|
|
Both breakouts share SDA, SCL, 3V3, and GND. The firmware checks both possible
|
|
7-bit I2C addresses for each device:
|
|
|
|
- ADXL345: `0x53` or `0x1D`; expected `DEVID` is `0xE5`.
|
|
- L3G4200D: `0x69` or `0x68`; expected `WHO_AM_I` is `0xD3`.
|
|
|
|
## Sensor configuration
|
|
|
|
- ADXL345: nominal 100 Hz output rate, full-resolution mode, +/-8 g. Nominal scale is
|
|
3.9 mg/LSB.
|
|
- L3G4200D: nominal 100 Hz output rate, LPF2 selected with a 25 Hz cutoff,
|
|
+/-500 dps. Nominal scale is 17.5 mdps/LSB.
|
|
|
|
The enclosure coordinate frame is:
|
|
|
|
- +X points right in the reference photograph.
|
|
- +Y points toward the top of the enclosure.
|
|
- +Z points out of the board toward the enclosure cover.
|
|
|
|
The L3G4200D already matches that frame. The ADXL345 mapping is:
|
|
|
|
```text
|
|
enclosure X = native Y
|
|
enclosure Y = -native X
|
|
enclosure Z = native Z
|
|
```
|
|
|
|
Software calibration is applied after enclosure-axis mapping. Accelerometer
|
|
offset and per-axis scale were measured with a six-face enclosure test. Gyroscope
|
|
zero-rate bias and polarity were measured; its 17.5 mdps/LSB scale remains the
|
|
nominal datasheet value. Sensor-native and mapped raw counts remain in every
|
|
record for diagnostics. No software filtering or sensor fusion is performed yet.
|
|
|
|
The ESP32-C3 polls at exactly 100 Hz, but each sensor has an independent internal
|
|
sample clock. The status registers are read immediately before each XYZ read so a
|
|
consumer can distinguish a fresh sample from a repeated poll and identify gyro
|
|
overruns. Hardware data-ready interrupts and FIFO acquisition are deferred to the
|
|
buffering milestone.
|
|
|
|
## Build and flash
|
|
|
|
ESP-IDF 6.0.2 is installed at:
|
|
|
|
```text
|
|
/Users/jay/.espressif/v6.0.2/esp-idf
|
|
```
|
|
|
|
For each new terminal:
|
|
|
|
```sh
|
|
source /Users/jay/.espressif/v6.0.2/esp-idf/export.sh
|
|
idf.py build
|
|
idf.py -p /dev/cu.usbmodem1134101 flash monitor
|
|
```
|
|
|
|
Exit the serial monitor with `Ctrl-]`.
|
|
|
|
## USB output
|
|
|
|
After startup metadata, records use CSV:
|
|
|
|
```text
|
|
sequence,poll_timestamp_us,accel_x_raw,accel_y_raw,accel_z_raw,gyro_x_raw,gyro_y_raw,gyro_z_raw,accel_x_mg,accel_y_mg,accel_z_mg,gyro_x_mdps,gyro_y_mdps,gyro_z_mdps,accel_native_x_raw,accel_native_y_raw,accel_native_z_raw,gyro_native_x_raw,gyro_native_y_raw,gyro_native_z_raw,accel_int_source,gyro_status,loop_overrun_count
|
|
```
|
|
|
|
`poll_timestamp_us` is the ESP32-C3 monotonic time immediately before the status
|
|
and data reads. It is not the sensors' physical sample time. The axes in the first
|
|
six sample columns use the enclosure frame above. Calibrated acceleration is in
|
|
integer milligravity (`mg`), and bias-corrected angular rate is in integer
|
|
millidegrees per second (`mdps`). Native columns remain available for diagnostics.
|
|
|
|
Status bits:
|
|
|
|
- `accel_int_source & 0x80`: an unread ADXL345 sample existed when status was
|
|
checked. If clear, treat the following sample as stale/untrusted; a sample can
|
|
arrive in the short interval between the status and data transactions.
|
|
- `accel_int_source & 0x01`: ADXL345 unread data was overwritten.
|
|
- `gyro_status & 0x08`: L3G4200D sample is fresh.
|
|
- `gyro_status & 0x80`: L3G4200D data overran before it was read.
|
|
- `loop_overrun_count`: cumulative acquisition deadlines missed; the loop
|
|
resynchronizes after a miss instead of issuing catch-up bursts.
|
|
|
|
The capture tool auto-detects a single `/dev/cu.usbmodem*` device, writes only
|
|
validated numeric records to a real CSV, and reports sequence or timing problems:
|
|
|
|
```sh
|
|
python tools/capture_serial.py
|
|
```
|